Filter Bags Dust Collector

Dust collector filter bags

Dust collector filter bags must be of the automatic self-cleaning variety (reverse air or pulse jet), depending on what is ideal for the application. The filter bags Dust Collector should be cleaned with compressed air using the preferable pulse-jet type. The Vendor is expected to provide all pressure regulators and filters needed for the operation of the bag houses, as well as to specify the required air pressure (normal plant air is typically available at a nominal 6-8 bar).

We offer dust collector filter bags made of materials like glass fiber, acrylic, Nylon, polyester, polypropylene, PTFE, P84, and cotton. We are positioned among the leading Indian-based manufacturers of dust collection bags. These pleated dust collection bags offer great performance that lasts for a very long time. Our pleated dust collection bags are extensively utilized in industries like metallurgy, fertilizers, chemicals, pollution control, Abrasive sand blasting machine, Shot blasting machine processes & wood working.

Only non-woven needle-punched cloth can be utilized in a bag filter system for reverse jet and pulse jet dust collectors because it can capture fine particles while releasing fresh air into the atmosphere.

Bag House Dust Collector

The dust hopper in the bag filter housing must be completely filled with dust. The appliance must have one airtight inspection door and internal baffle plates for equal air dispersion (min. size 600 mm x 600 mm).

A solid-state sequential timer is required to regulate the cleaning frequency. The positioning of the parts must make it simple to assemble, install, replace damaged parts, and gain access for cleaning, maintenance, and repair.

Industrial dust collector filter bags and bag house dust collector cleaning mechanisms must have easy access for maintenance from the clean air side. All units that have a capacity of 17,000 Nm3/h or more must have a walk-in plenum. Internal pathways and gasketed access doors must be offered. Gaskets for doors must be appropriate for both positive and negative pressure. If a bag houses, the replacement must be done from the top clean side.

For the dust collector Filter Bag and fan to operate, all relevant controls must be available, including start/stop push buttons and an emergency stop button that must be approved by the owner. Legs made of structural steel that can handle the weight of the collector, hopper and a full load of dust must be provided. The hopper valley angle must be at least 60°.

Metric manometers must be permanently linked to every Bag House Dust Collector. Dust collectors must be fitted with a differential pressure gauge with contacts for remote high level indication and alarm if their filter area is 50 m2 or more. Bolts that are exposed to the elements must be made of stainless steel or another metal that resists corrosion.

Types of Filter Bag Dust Collector

The kind of filter bag dust Collector your dust collector will require to run at its best performance and effectiveness will depend on the kind of Abrasive Sand Blasting machine or shot Blasting Machine you have and the particular operating circumstances.

Cotton (woven) Bag Filter Dust Collector

180°F is the typical maximum continuous operating temperature. General applications include cleaning rooms, cleaning atmospheric air, woodworking applications, cement & rock products, and other general applications handling ambient air. These are generally used on shaker type dust collectors. Low chemical resistance and severe flammability. Cotton Bag Filter Dust Collector filters are not advised where mineral acids and oxidizing chemicals are present, despite their strong chemical resistance in dry, ambient circumstances. These filters offer good resistance to both flex and flat abrasion. Where static charge tends to hold dust cake on other fibers, cotton offers exceptional clean-down capabilities. There is flame-retardant cotton available.

Polyester Bag Filter Dust Collector

275°F is the typical maximum continuous working temperature. Polyester Bag Filter Dust Collector felts offer very good resistance to chemicals, abrasion, and dry heat degradation. They are the most typical kind of filter bag used today and provide great dimensional stability. With the exception of Aramid, polyester Bag Filter Dust Collector is the best synthetic material for dry heat applications. Polyester is not a good material for wet heat and, in some cases, is susceptible to hydrolytic destruction. Except for very concentrated nitric, sulfuric, and carbolic acids, polyester offers good resistance to most mineral and organic acids. Additionally, polyester offers great resistance to most organic solvents and good resistance to most oxidizing agents.

Nylon Bag Filter Dust Collector

250°F is the typical maximum continuous operating temperature. For applications involving highly abrasive particles, nylon felt is frequently employed. Under most circumstances, Nylon Bag Filter Dust Collector has good resistance to alkalis, although the majority of mineral oxides cause deterioration and partial breakdown. Complete deterioration could be brought on by high temperatures and concentrations. This media holds up to common organic solvents very well.

Polypropylene Bag Filter Dust Collector

170°F is the typical maximum continuous working temperature. Felt made of polypropylene is utilized in general situations where other fibers are attacked by chemicals and moisture. High strength and exceptional resilience to most acids and alkalis are two features of polypropylene Bag Filter Dust Collector. The smoothness of the fibers allows for good cake release and blinding resistance. There is almost no moisture absorption. This fabric media offers generally good resistance to alkalis with the exception of sodium and potassium hydroxide over 200°F and extremely good resistance to both mineral and organic acids.

Dust Collector Filter Bag material and assembly

Filter Bag Dust Collector or Bag House Dust Collector is required as part of the bag construction.

• Plugs that are about 10%. Until a replacement bag can be placed, these will be used to seal the venturi of a leaky bag.
• Bag support cages must be built out of at least 3 mm galvanized steel wires in a single piece. The cage must include a venturi, if necessary. With a galvanized steel cap welded to the wire cage, the bottom of the cage must be sealed. The minimum number of vertical wires in the wire cage is 8, and the maximum horizontal ring spacing is 200 mm.
• The bag cage is coated in 75 percent epoxy to prevent corrosion.
• Make bag removal easier.
• The Venturi (if required).
• Fastening devices made of stainless steel.
• Sealing gasket

Filter Bag House Dust Collector Manufacturers

Ambica Enterprises is the Leading Filter Bag House Dust Collector Manufacturers & Suppliers of Dust Collector Filter Bags in India at a low price. We are also providing Sand Blasting Machine, portable Shot Blasting Machine, sand blasting cabinet, sand blasting nozzle, sand blasting helmet, portable sand blasting machine, shot blasting room, abrasive blasting machine, thermal spray guns, hvof gun, wire flame spray gun, thermal spray wire, metallizing wire, abrasive media, stainless steel shot, steel grit, abrasive garnet, plastic abrasive.